Note

Click here to download the full example code

Here we give some background information on filtering in general,
and how it is done in MNE-Python in particular.
Recommended reading for practical applications of digital
filter design can be found in Parks & Burrus [1] and
Ifeachor and Jervis [2], and for filtering in an
M/EEG context we recommend reading Widmann *et al.* 2015 [7].
To see how to use the default filters in MNE-Python on actual data, see
the Filtering and resampling data
tutorial.

The practical issues with filtering electrophysiological data are covered
well by Widmann *et al.* in [7], in a follow-up to an article where they
conclude with this statement:

Filtering can result in considerable distortions of the time course (and amplitude) of a signal as demonstrated by VanRullen (2011) [[3]]. Thus, filtering should not be used lightly. However, if effects of filtering are cautiously considered and filter artifacts are minimized, a valid interpretation of the temporal dynamics of filtered electrophysiological data is possible and signals missed otherwise can be detected with filtering.

In other words, filtering can increase SNR, but if it is not used carefully, it can distort data. Here we hope to cover some filtering basics so users can better understand filtering tradeoffs, and why MNE-Python has chosen particular defaults.

Let’s get some of the basic math down. In the frequency domain, digital filters have a transfer function that is given by:

\[\begin{split}H(z) &= \frac{b_0 + b_1 z^{-1} + b_2 z^{-2} + ... + b_M z^{-M}}
{1 + a_1 z^{-1} + a_2 z^{-2} + ... + a_N z^{-M}} \\
&= \frac{\sum_0^Mb_kz^{-k}}{\sum_1^Na_kz^{-k}}\end{split}\]

In the time domain, the numerator coefficients \(b_k\) and denominator coefficients \(a_k\) can be used to obtain our output data \(y(n)\) in terms of our input data \(x(n)\) as:

(1)¶\[\begin{split} y(n) &= b_0 x(n) + b_1 x(n-1) + ... + b_M x(n-M)
- a_1 y(n-1) - a_2 y(n - 2) - ... - a_N y(n - N)\\
&= \sum_0^M b_k x(n-k) - \sum_1^N a_k y(n-k)\end{split}\]

In other words, the output at time \(n\) is determined by a sum over:

- The numerator coefficients \(b_k\), which get multiplied by the previous input \(x(n-k)\) values, and
- The denominator coefficients \(a_k\), which get multiplied by the previous output \(y(n-k)\) values.

Note that these summations in (1) correspond nicely to (1) a weighted moving average and (2) an autoregression.

Filters are broken into two classes: FIR (finite impulse response) and IIR (infinite impulse response) based on these coefficients. FIR filters use a finite number of numerator coefficients \(b_k\) (\(\forall k, a_k=0\)), and thus each output value of \(y(n)\) depends only on the \(M\) previous input values. IIR filters depend on the previous input and output values, and thus can have effectively infinite impulse responses.

As outlined in [1], FIR and IIR have different tradeoffs:

- A causal FIR filter can be linear-phase – i.e., the same time delay across all frequencies – whereas a causal IIR filter cannot. The phase and group delay characteristics are also usually better for FIR filters.
- IIR filters can generally have a steeper cutoff than an FIR filter of equivalent order.
- IIR filters are generally less numerically stable, in part due to accumulating error (due to its recursive calculations).

In MNE-Python we default to using FIR filtering. As noted in Widmann *et al.*
2015 [7]:

Despite IIR filters often being considered as computationally more efficient, they are recommended only when high throughput and sharp cutoffs are required (Ifeachor and Jervis, 2002 [2], p. 321), …FIR filters are easier to control, are always stable, have a well-defined passband, can be corrected to zero-phase without additional computations, and can be converted to minimum-phase. We therefore recommend FIR filters for most purposes in electrophysiological data analysis.

When designing a filter (FIR or IIR), there are always tradeoffs that need to be considered, including but not limited to:

- Ripple in the pass-band
- Attenuation of the stop-band
- Steepness of roll-off
- Filter order (i.e., length for FIR filters)
- Time-domain ringing

In general, the sharper something is in frequency, the broader it is in time, and vice-versa. This is a fundamental time-frequency tradeoff, and it will show up below.

First we will focus first on FIR filters, which are the default filters used by MNE-Python.

Here we’ll try designing a low-pass filter, and look at trade-offs in terms of time- and frequency-domain filter characteristics. Later, in Applying FIR filters, we’ll look at how such filters can affect signals when they are used.

First let’s import some useful tools for filtering, and set some default values for our data that are reasonable for M/EEG data.

```
import numpy as np
from scipy import signal, fftpack
import matplotlib.pyplot as plt
from mne.time_frequency.tfr import morlet
from mne.viz import plot_filter, plot_ideal_filter
import mne
sfreq = 1000.
f_p = 40.
flim = (1., sfreq / 2.) # limits for plotting
```

Take for example an ideal low-pass filter, which would give a value of 1 in the pass-band (up to frequency \(f_p\)) and a value of 0 in the stop-band (down to frequency \(f_s\)) such that \(f_p=f_s=40\) Hz here (shown to a lower limit of -60 dB for simplicity):

```
nyq = sfreq / 2. # the Nyquist frequency is half our sample rate
freq = [0, f_p, f_p, nyq]
gain = [1, 1, 0, 0]
third_height = np.array(plt.rcParams['figure.figsize']) * [1, 1. / 3.]
ax = plt.subplots(1, figsize=third_height)[1]
plot_ideal_filter(freq, gain, ax, title='Ideal %s Hz lowpass' % f_p, flim=flim)
```

This filter hypothetically achieves zero ripple in the frequency domain, perfect attenuation, and perfect steepness. However, due to the discontunity in the frequency response, the filter would require infinite ringing in the time domain (i.e., infinite order) to be realized. Another way to think of this is that a rectangular window in frequency is actually sinc function in time, which requires an infinite number of samples, and thus infinite time, to represent. So although this filter has ideal frequency suppression, it has poor time-domain characteristics.

Let’s try to naïvely make a brick-wall filter of length 0.1 sec, and look at the filter itself in the time domain and the frequency domain:

```
n = int(round(0.1 * sfreq)) + 1
t = np.arange(-n // 2, n // 2) / sfreq # center our sinc
h = np.sinc(2 * f_p * t) / (4 * np.pi)
plot_filter(h, sfreq, freq, gain, 'Sinc (0.1 sec)', flim=flim)
```

This is not so good! Making the filter 10 times longer (1 sec) gets us a bit better stop-band suppression, but still has a lot of ringing in the time domain. Note the x-axis is an order of magnitude longer here, and the filter has a correspondingly much longer group delay (again equal to half the filter length, or 0.5 seconds):

```
n = int(round(1. * sfreq)) + 1
t = np.arange(-n // 2, n // 2) / sfreq
h = np.sinc(2 * f_p * t) / (4 * np.pi)
plot_filter(h, sfreq, freq, gain, 'Sinc (1.0 sec)', flim=flim)
```

Let’s make the stop-band tighter still with a longer filter (10 sec), with a resulting larger x-axis:

```
n = int(round(10. * sfreq)) + 1
t = np.arange(-n // 2, n // 2) / sfreq
h = np.sinc(2 * f_p * t) / (4 * np.pi)
plot_filter(h, sfreq, freq, gain, 'Sinc (10.0 sec)', flim=flim)
```

Now we have very sharp frequency suppression, but our filter rings for the entire second. So this naïve method is probably not a good way to build our low-pass filter.

Fortunately, there are multiple established methods to design FIR filters based on desired response characteristics. These include:

- The Remez algorithm (
`scipy.signal.remez()`

, MATLAB firpm)- Windowed FIR design (
`scipy.signal.firwin2()`

, MATLAB fir2 and`scipy.signal.firwin()`

)- Least squares designs (
`scipy.signal.firls()`

, MATLAB firls)- Frequency-domain design (construct filter in Fourier domain and use an
`IFFT`

to invert it)

Note

Remez and least squares designs have advantages when there are “do not care” regions in our frequency response. However, we want well controlled responses in all frequency regions. Frequency-domain construction is good when an arbitrary response is desired, but generally less clean (due to sampling issues) than a windowed approach for more straightfroward filter applications. Since our filters (low-pass, high-pass, band-pass, band-stop) are fairly simple and we require precise control of all frequency regions, here we will use and explore primarily windowed FIR design.

If we relax our frequency-domain filter requirements a little bit, we can
use these functions to construct a lowpass filter that instead has a
*transition band*, or a region between the pass frequency \(f_p\)
and stop frequency \(f_s\), e.g.:

```
trans_bandwidth = 10 # 10 Hz transition band
f_s = f_p + trans_bandwidth # = 50 Hz
freq = [0., f_p, f_s, nyq]
gain = [1., 1., 0., 0.]
ax = plt.subplots(1, figsize=third_height)[1]
title = '%s Hz lowpass with a %s Hz transition' % (f_p, trans_bandwidth)
plot_ideal_filter(freq, gain, ax, title=title, flim=flim)
```

Accepting a shallower roll-off of the filter in the frequency domain makes
our time-domain response potentially much better. We end up with a
smoother slope through the transition region, but a *much* cleaner time
domain signal. Here again for the 1 sec filter:

```
h = signal.firwin2(n, freq, gain, nyq=nyq)
plot_filter(h, sfreq, freq, gain, 'Windowed 10-Hz transition (1.0 sec)',
flim=flim)
```

Since our lowpass is around 40 Hz with a 10 Hz transition, we can actually use a shorter filter (5 cycles at 10 Hz = 0.5 sec) and still get okay stop-band attenuation:

```
n = int(round(sfreq * 0.5)) + 1
h = signal.firwin2(n, freq, gain, nyq=nyq)
plot_filter(h, sfreq, freq, gain, 'Windowed 10-Hz transition (0.5 sec)',
flim=flim)
```

But then if we shorten the filter too much (2 cycles of 10 Hz = 0.2 sec), our effective stop frequency gets pushed out past 60 Hz:

```
n = int(round(sfreq * 0.2)) + 1
h = signal.firwin2(n, freq, gain, nyq=nyq)
plot_filter(h, sfreq, freq, gain, 'Windowed 10-Hz transition (0.2 sec)',
flim=flim)
```

If we want a filter that is only 0.1 seconds long, we should probably use something more like a 25 Hz transition band (0.2 sec = 5 cycles @ 25 Hz):

```
trans_bandwidth = 25
f_s = f_p + trans_bandwidth
freq = [0, f_p, f_s, nyq]
h = signal.firwin2(n, freq, gain, nyq=nyq)
plot_filter(h, sfreq, freq, gain, 'Windowed 50-Hz transition (0.2 sec)',
flim=flim)
```

So far we have only discussed *acausal* filtering, which means that each
sample at each time point \(t\) is filtered using samples that come
after (\(t + \Delta t\)) *and* before (\(t - \Delta t\)) \(t\).
In this sense, each sample is influenced by samples that come both before
and after it. This is useful in many cases, espcially because it does not
delay the timing of events.

However, sometimes it can be beneficial to use *causal* filtering,
whereby each sample \(t\) is filtered only using time points that came
after it.

Note that the delay is variable (whereas for linear/zero-phase filters it is constant) but small in the pass-band. Unlike zero-phase filters, which require time-shifting backward the output of a linear-phase filtering stage (and thus becoming acausal), minimum-phase filters do not require any compensation to achieve small delays in the passband. Note that as an artifact of the minimum phase filter construction step, the filter does not end up being as steep as the linear/zero-phase version.

We can construct a minimum-phase filter from our existing linear-phase
filter with the `minimum_phase`

function (that will be in SciPy 0.19’s
`scipy.signal`

), and note that the falloff is not as steep:

```
h_min = mne.fixes.minimum_phase(h)
plot_filter(h_min, sfreq, freq, gain, 'Minimum-phase', flim=flim)
```

Now lets look at some practical effects of these filters by applying them to some data.

Let’s construct a Gaussian-windowed sinusoid (i.e., Morlet imaginary part) plus noise (random + line). Note that the original, clean signal contains frequency content in both the pass band and transition bands of our low-pass filter.

```
dur = 10.
center = 2.
morlet_freq = f_p
tlim = [center - 0.2, center + 0.2]
tticks = [tlim[0], center, tlim[1]]
flim = [20, 70]
x = np.zeros(int(sfreq * dur) + 1)
blip = morlet(sfreq, [morlet_freq], n_cycles=7)[0].imag / 20.
n_onset = int(center * sfreq) - len(blip) // 2
x[n_onset:n_onset + len(blip)] += blip
x_orig = x.copy()
rng = np.random.RandomState(0)
x += rng.randn(len(x)) / 1000.
x += np.sin(2. * np.pi * 60. * np.arange(len(x)) / sfreq) / 2000.
```

Filter it with a shallow cutoff, linear-phase FIR (which allows us to compensate for the constant filter delay):

```
transition_band = 0.25 * f_p
f_s = f_p + transition_band
filter_dur = 6.6 / transition_band / 2. # sec
n = int(sfreq * filter_dur)
freq = [0., f_p, f_s, sfreq / 2.]
gain = [1., 1., 0., 0.]
# This would be equivalent:
h = mne.filter.create_filter(x, sfreq, l_freq=None, h_freq=f_p,
fir_design='firwin')
x_v16 = np.convolve(h, x)[len(h) // 2:]
plot_filter(h, sfreq, freq, gain, 'MNE-Python 0.16 default', flim=flim)
```

Out:

```
Setting up low-pass filter at 40 Hz
h_trans_bandwidth chosen to be 10.0 Hz
Filter length of 331 samples (0.331 sec) selected
```

Filter it with a different design mode `fir_design="firwin2"`

, and also
compensate for the constant filter delay. This method does not produce
quite as sharp a transition compared to `fir_design="firwin"`

, despite
being twice as long:

```
transition_band = 0.25 * f_p
f_s = f_p + transition_band
filter_dur = 6.6 / transition_band # sec
n = int(sfreq * filter_dur)
freq = [0., f_p, f_s, sfreq / 2.]
gain = [1., 1., 0., 0.]
# This would be equivalent:
# h = signal.firwin2(n, freq, gain, nyq=sfreq / 2.)
h = mne.filter.create_filter(x, sfreq, l_freq=None, h_freq=f_p,
fir_design='firwin2')
x_v14 = np.convolve(h, x)[len(h) // 2:]
plot_filter(h, sfreq, freq, gain, 'MNE-Python 0.14 default', flim=flim)
```

Out:

```
Setting up low-pass filter at 40 Hz
h_trans_bandwidth chosen to be 10.0 Hz
Filter length of 660 samples (0.660 sec) selected
```

This is actually set to become the default type of filter used in MNE-Python in 0.14 (see Defaults in MNE-Python).

Let’s also filter with the MNE-Python 0.13 default, which is a long-duration, steep cutoff FIR that gets applied twice:

```
transition_band = 0.5 # Hz
f_s = f_p + transition_band
filter_dur = 10. # sec
n = int(sfreq * filter_dur)
freq = [0., f_p, f_s, sfreq / 2.]
gain = [1., 1., 0., 0.]
# This would be equivalent
# h = signal.firwin2(n, freq, gain, nyq=sfreq / 2.)
h = mne.filter.create_filter(x, sfreq, l_freq=None, h_freq=f_p,
h_trans_bandwidth=transition_band,
filter_length='%ss' % filter_dur,
fir_design='firwin2')
x_v13 = np.convolve(np.convolve(h, x)[::-1], h)[::-1][len(h) - 1:-len(h) - 1]
plot_filter(h, sfreq, freq, gain, 'MNE-Python 0.13 default', flim=flim)
```

Out:

```
Setting up low-pass filter at 40 Hz
Filter length of 10000 samples (10.000 sec) selected
```

Let’s also filter it with the MNE-C default, which is a long-duration steep-slope FIR filter designed using frequency-domain techniques:

```
h = mne.filter.design_mne_c_filter(sfreq, l_freq=None, h_freq=f_p + 2.5)
x_mne_c = np.convolve(h, x)[len(h) // 2:]
transition_band = 5 # Hz (default in MNE-C)
f_s = f_p + transition_band
freq = [0., f_p, f_s, sfreq / 2.]
gain = [1., 1., 0., 0.]
plot_filter(h, sfreq, freq, gain, 'MNE-C default', flim=flim)
```

Out:

```
filter : 0.000 ... 42.5 Hz bins : 0 ... 348 of 4097 hpw : 3 lpw : 20
```

And now an example of a minimum-phase filter:

```
h = mne.filter.create_filter(x, sfreq, l_freq=None, h_freq=f_p,
phase='minimum', fir_design='firwin')
x_min = np.convolve(h, x)
transition_band = 0.25 * f_p
f_s = f_p + transition_band
filter_dur = 6.6 / transition_band # sec
n = int(sfreq * filter_dur)
freq = [0., f_p, f_s, sfreq / 2.]
gain = [1., 1., 0., 0.]
plot_filter(h, sfreq, freq, gain, 'Minimum-phase filter', flim=flim)
```

Out:

```
Setting up low-pass filter at 40 Hz
h_trans_bandwidth chosen to be 10.0 Hz
Filter length of 331 samples (0.331 sec) selected
```

Both the MNE-Python 0.13 and MNE-C filhters have excellent frequency attenuation, but it comes at a cost of potential ringing (long-lasting ripples) in the time domain. Ringing can occur with steep filters, especially on signals with frequency content around the transition band. Our Morlet wavelet signal has power in our transition band, and the time-domain ringing is thus more pronounced for the steep-slope, long-duration filter than the shorter, shallower-slope filter:

```
axes = plt.subplots(1, 2)[1]
def plot_signal(x, offset):
t = np.arange(len(x)) / sfreq
axes[0].plot(t, x + offset)
axes[0].set(xlabel='Time (sec)', xlim=t[[0, -1]])
X = fftpack.fft(x)
freqs = fftpack.fftfreq(len(x), 1. / sfreq)
mask = freqs >= 0
X = X[mask]
freqs = freqs[mask]
axes[1].plot(freqs, 20 * np.log10(np.maximum(np.abs(X), 1e-16)))
axes[1].set(xlim=flim)
yticks = np.arange(7) / -30.
yticklabels = ['Original', 'Noisy', 'FIR-firwin (0.16)', 'FIR-firwin2 (0.14)',
'FIR-steep (0.13)', 'FIR-steep (MNE-C)', 'Minimum-phase']
plot_signal(x_orig, offset=yticks[0])
plot_signal(x, offset=yticks[1])
plot_signal(x_v16, offset=yticks[2])
plot_signal(x_v14, offset=yticks[3])
plot_signal(x_v13, offset=yticks[4])
plot_signal(x_mne_c, offset=yticks[5])
plot_signal(x_min, offset=yticks[6])
axes[0].set(xlim=tlim, title='FIR, Lowpass=%d Hz' % f_p, xticks=tticks,
ylim=[-0.200, 0.025], yticks=yticks, yticklabels=yticklabels,)
for text in axes[0].get_yticklabels():
text.set(rotation=45, size=8)
axes[1].set(xlim=flim, ylim=(-60, 10), xlabel='Frequency (Hz)',
ylabel='Magnitude (dB)')
mne.viz.tight_layout()
plt.show()
```

MNE-Python also offers IIR filtering functionality that is based on the
methods from `scipy.signal`

. Specifically, we use the general-purpose
functions `scipy.signal.iirfilter()`

and `scipy.signal.iirdesign()`

,
which provide unified interfaces to IIR filter design.

Let’s continue with our design of a 40 Hz low-pass filter, and look at some trade-offs of different IIR filters.

Often the default IIR filter is a Butterworth filter, which is designed
to have a *maximally flat pass-band*. Let’s look at a few orders of filter,
i.e., a few different number of coefficients used and therefore steepness
of the filter:

Note

Notice that the group delay (which is related to the phase) of
the IIR filters below are not constant. In the FIR case, we can
design so-called linear-phase filters that have a constant group
delay, and thus compensate for the delay (making the filter
acausal) if necessary. This cannot be done with IIR filters, as
they have a non-linear phase (non-constant group delay). As the
filter order increases, the phase distortion near and in the
transition band worsens. However, if acausal (forward-backward)
filtering can be used, e.g. with `scipy.signal.filtfilt()`

,
these phase issues can theoretically be mitigated.

```
sos = signal.iirfilter(2, f_p / nyq, btype='low', ftype='butter', output='sos')
plot_filter(dict(sos=sos), sfreq, freq, gain, 'Butterworth order=2', flim=flim)
# Eventually this will just be from scipy signal.sosfiltfilt, but 0.18 is
# not widely adopted yet (as of June 2016), so we use our wrapper...
sosfiltfilt = mne.fixes.get_sosfiltfilt()
x_shallow = sosfiltfilt(sos, x)
```

The falloff of this filter is not very steep.

Note

Here we have made use of second-order sections (SOS)
by using `scipy.signal.sosfilt()`

and, under the
hood, `scipy.signal.zpk2sos()`

when passing the
`output='sos'`

keyword argument to
`scipy.signal.iirfilter()`

. The filter definitions
given in tut_filtering_basics use the polynomial
numerator/denominator (sometimes called “tf”) form `(b, a)`

,
which are theoretically equivalent to the SOS form used here.
In practice, however, the SOS form can give much better results
due to issues with numerical precision (see
`scipy.signal.sosfilt()`

for an example), so SOS should be
used when possible to do IIR filtering.

Let’s increase the order, and note that now we have better attenuation, with a longer impulse response:

```
sos = signal.iirfilter(8, f_p / nyq, btype='low', ftype='butter', output='sos')
plot_filter(dict(sos=sos), sfreq, freq, gain, 'Butterworth order=8', flim=flim)
x_steep = sosfiltfilt(sos, x)
```

There are other types of IIR filters that we can use. For a complete list,
check out the documentation for `scipy.signal.iirdesign()`

. Let’s
try a Chebychev (type I) filter, which trades off ripple in the pass-band
to get better attenuation in the stop-band:

```
sos = signal.iirfilter(8, f_p / nyq, btype='low', ftype='cheby1', output='sos',
rp=1) # dB of acceptable pass-band ripple
plot_filter(dict(sos=sos), sfreq, freq, gain,
'Chebychev-1 order=8, ripple=1 dB', flim=flim)
```

And if we can live with even more ripple, we can get it slightly steeper, but the impulse response begins to ring substantially longer (note the different x-axis scale):

```
sos = signal.iirfilter(8, f_p / nyq, btype='low', ftype='cheby1', output='sos',
rp=6)
plot_filter(dict(sos=sos), sfreq, freq, gain,
'Chebychev-1 order=8, ripple=6 dB', flim=flim)
```

Now let’s look at how our shallow and steep Butterworth IIR filters perform on our Morlet signal from before:

```
axes = plt.subplots(1, 2)[1]
yticks = np.arange(4) / -30.
yticklabels = ['Original', 'Noisy', 'Butterworth-2', 'Butterworth-8']
plot_signal(x_orig, offset=yticks[0])
plot_signal(x, offset=yticks[1])
plot_signal(x_shallow, offset=yticks[2])
plot_signal(x_steep, offset=yticks[3])
axes[0].set(xlim=tlim, title='IIR, Lowpass=%d Hz' % f_p, xticks=tticks,
ylim=[-0.125, 0.025], yticks=yticks, yticklabels=yticklabels,)
for text in axes[0].get_yticklabels():
text.set(rotation=45, size=8)
axes[1].set(xlim=flim, ylim=(-60, 10), xlabel='Frequency (Hz)',
ylabel='Magnitude (dB)')
mne.viz.adjust_axes(axes)
mne.viz.tight_layout()
plt.show()
```

Multiple recent papers have noted potential risks of drawing errant inferences due to misapplication of filters.

Filters in general, especially those that are acausal (zero-phase), can make activity appear to occur earlier or later than it truly did. As mentioned in VanRullen 2011 [3], investigations of commonly (at the time) used low-pass filters created artifacts when they were applied to smulated data. However, such deleterious effects were minimal in many real-world examples in Rousselet 2012 [5].

Perhaps more revealing, it was noted in Widmann & Schröger 2012 [6] that the problematic low-pass filters from VanRullen 2011 [3]:

- Used a least-squares design (like
`scipy.signal.firls()`

) that included “do-not-care” transition regions, which can lead to uncontrolled behavior.- Had a filter length that was independent of the transition bandwidth, which can cause excessive ringing and signal distortion.

When it comes to high-pass filtering, using corner frequencies above 0.1 Hz
were found in Acunzo *et al.* 2012 [4] to:

“…generate a systematic bias easily leading to misinterpretations of neural activity.”

In a related paper, Widmann *et al.* 2015 [7] also came to suggest a 0.1 Hz
highpass. And more evidence followed in Tanner *et al.* 2015 [8] of such
distortions. Using data from language ERP studies of semantic and syntactic
processing (i.e., N400 and P600), using a high-pass above 0.3 Hz caused
significant effects to be introduced implausibly early when compared to the
unfiltered data. From this, the authors suggested the optimal high-pass
value for language processing to be 0.1 Hz.

We can recreate a problematic simulation from Tanner *et al.* 2015 [8]:

“The simulated component is a single-cycle cosine wave with an amplitude of 5µV, onset of 500 ms poststimulus, and duration of 800 ms. The simulated component was embedded in 20 s of zero values to avoid filtering edge effects… Distortions [were] caused by 2 Hz low-pass and high-pass filters… No visible distortion to the original waveform [occurred] with 30 Hz low-pass and 0.01 Hz high-pass filters… Filter frequencies correspond to the half-amplitude (-6 dB) cutoff (12 dB/octave roll-off).”

Note

This simulated signal contains energy not just within the
pass-band, but also within the transition and stop-bands – perhaps
most easily understood because the signal has a non-zero DC value,
but also because it is a shifted cosine that has been
*windowed* (here multiplied by a rectangular window), which
makes the cosine and DC frequencies spread to other frequencies
(multiplication in time is convolution in frequency, so multiplying
by a rectangular window in the time domain means convolving a sinc
function with the impulses at DC and the cosine frequency in the
frequency domain).

```
x = np.zeros(int(2 * sfreq))
t = np.arange(0, len(x)) / sfreq - 0.2
onset = np.where(t >= 0.5)[0][0]
cos_t = np.arange(0, int(sfreq * 0.8)) / sfreq
sig = 2.5 - 2.5 * np.cos(2 * np.pi * (1. / 0.8) * cos_t)
x[onset:onset + len(sig)] = sig
iir_lp_30 = signal.iirfilter(2, 30. / sfreq, btype='lowpass')
iir_hp_p1 = signal.iirfilter(2, 0.1 / sfreq, btype='highpass')
iir_lp_2 = signal.iirfilter(2, 2. / sfreq, btype='lowpass')
iir_hp_2 = signal.iirfilter(2, 2. / sfreq, btype='highpass')
x_lp_30 = signal.filtfilt(iir_lp_30[0], iir_lp_30[1], x, padlen=0)
x_hp_p1 = signal.filtfilt(iir_hp_p1[0], iir_hp_p1[1], x, padlen=0)
x_lp_2 = signal.filtfilt(iir_lp_2[0], iir_lp_2[1], x, padlen=0)
x_hp_2 = signal.filtfilt(iir_hp_2[0], iir_hp_2[1], x, padlen=0)
xlim = t[[0, -1]]
ylim = [-2, 6]
xlabel = 'Time (sec)'
ylabel = r'Amplitude ($\mu$V)'
tticks = [0, 0.5, 1.3, t[-1]]
axes = plt.subplots(2, 2)[1].ravel()
for ax, x_f, title in zip(axes, [x_lp_2, x_lp_30, x_hp_2, x_hp_p1],
['LP$_2$', 'LP$_{30}$', 'HP$_2$', 'LP$_{0.1}$']):
ax.plot(t, x, color='0.5')
ax.plot(t, x_f, color='k', linestyle='--')
ax.set(ylim=ylim, xlim=xlim, xticks=tticks,
title=title, xlabel=xlabel, ylabel=ylabel)
mne.viz.adjust_axes(axes)
mne.viz.tight_layout()
plt.show()
```

Similarly, in a P300 paradigm reported by Kappenman & Luck 2010 [12], they found that applying a 1 Hz high-pass decreased the probaility of finding a significant difference in the N100 response, likely because the P300 response was smeared (and inverted) in time by the high-pass filter such that it tended to cancel out the increased N100. However, they nonetheless note that some high-passing can still be useful to deal with drifts in the data.

Even though these papers generally advise a 0.1 HZ or lower frequency for a high-pass, it is important to keep in mind (as most authors note) that filtering choices should depend on the frequency content of both the signal(s) of interest and the noise to be suppressed. For example, in some of the MNE-Python examples involving The sample data set, high-pass values of around 1 Hz are used when looking at auditory or visual N100 responses, because we analyze standard (not deviant) trials and thus expect that contamination by later or slower components will be limited.

In an evolving discussion, Tanner *et al.* 2015 [8] suggest using baseline
correction to remove slow drifts in data. However, Maess *et al.* 2016 [9]
suggest that baseline correction, which is a form of high-passing, does
not offer substantial advantages over standard high-pass filtering.
Tanner *et al.* [10] rebutted that baseline correction can correct for
problems with filtering.

To see what they mean, consider again our old simulated signal `x`

from
before:

```
def baseline_plot(x):
all_axes = plt.subplots(3, 2)[1]
for ri, (axes, freq) in enumerate(zip(all_axes, [0.1, 0.3, 0.5])):
for ci, ax in enumerate(axes):
if ci == 0:
iir_hp = signal.iirfilter(4, freq / sfreq, btype='highpass',
output='sos')
x_hp = sosfiltfilt(iir_hp, x, padlen=0)
else:
x_hp -= x_hp[t < 0].mean()
ax.plot(t, x, color='0.5')
ax.plot(t, x_hp, color='k', linestyle='--')
if ri == 0:
ax.set(title=('No ' if ci == 0 else '') +
'Baseline Correction')
ax.set(xticks=tticks, ylim=ylim, xlim=xlim, xlabel=xlabel)
ax.set_ylabel('%0.1f Hz' % freq, rotation=0,
horizontalalignment='right')
mne.viz.adjust_axes(axes)
mne.viz.tight_layout()
plt.suptitle(title)
plt.show()
baseline_plot(x)
```

In response, Maess *et al.* 2016 [11] note that these simulations do not
address cases of pre-stimulus activity that is shared across conditions, as
applying baseline correction will effectively copy the topology outside the
baseline period. We can see this if we give our signal `x`

with some
consistent pre-stimulus activity, which makes everything look bad.

Note

An important thing to keep in mind with these plots is that they are for a single simulated sensor. In multielectrode recordings the topology (i.e., spatial pattiern) of the pre-stimulus activity will leak into the post-stimulus period. This will likely create a spatially varying distortion of the time-domain signals, as the averaged pre-stimulus spatial pattern gets subtracted from the sensor time courses.

Putting some activity in the baseline period:

Both groups seem to acknowledge that the choices of filtering cutoffs, and perhaps even the application of baseline correction, depend on the characteristics of the data being investigated, especially when it comes to:

- The frequency content of the underlying evoked activity relative to the filtering parameters.
- The validity of the assumption of no consistent evoked activity in the baseline period.

We thus recommend carefully applying baseline correction and/or high-pass values based on the characteristics of the data to be analyzed.

Most often, filtering in MNE-Python is done at the `mne.io.Raw`

level,
and thus `mne.io.Raw.filter()`

is used. This function under the hood
(among other things) calls `mne.filter.filter_data()`

to actually
filter the data, which by default applies a zero-phase FIR filter designed
using `scipy.signal.firwin()`

. In Widmann *et al.* 2015 [7], they
suggest a specific set of parameters to use for high-pass filtering,
including:

“… providing a transition bandwidth of 25% of the lower passband edge but, where possible, not lower than 2 Hz and otherwise the distance from the passband edge to the critical frequency.”

In practice, this means that for each high-pass value `l_freq`

or
low-pass value `h_freq`

below, you would get this corresponding
`l_trans_bandwidth`

or `h_trans_bandwidth`

, respectively,
if the sample rate were 100 Hz (i.e., Nyquist frequency of 50 Hz):

l_freq or h_freq | l_trans_bandwidth | h_trans_bandwidth |
---|---|---|

0.01 | 0.01 | 2.0 |

0.1 | 0.1 | 2.0 |

1.0 | 1.0 | 2.0 |

2.0 | 2.0 | 2.0 |

4.0 | 2.0 | 2.0 |

8.0 | 2.0 | 2.0 |

10.0 | 2.5 | 2.5 |

20.0 | 5.0 | 5.0 |

40.0 | 10.0 | 10.0 |

45.0 | 11.25 | 5.0 |

48.0 | 12.0 | 2.0 |

MNE-Python has adopted this definition for its high-pass (and low-pass)
transition bandwidth choices when using `l_trans_bandwidth='auto'`

and
`h_trans_bandwidth='auto'`

.

To choose the filter length automatically with `filter_length='auto'`

,
the reciprocal of the shortest transition bandwidth is used to ensure
decent attenuation at the stop frequency. Specifically, the reciprocal
(in samples) is multiplied by 3.1, 3.3, or 5.0 for the Hann, Hamming,
or Blackman windows, respectively as selected by the `fir_window`

argument for `fir_design='firwin'`

, and double these for
`fir_design='firwin2'`

mode.

Note

For `fir_design='firwin2'`

, the multiplicative factors are
doubled compared to what is given in Ifeachor and Jervis [2]
(p. 357), as `scipy.signal.firwin2()`

has a smearing effect
on the frequency response, which we compensate for by
increasing the filter length. This is why
`fir_desgin='firwin'`

is preferred to `fir_design='firwin2'`

.

In 0.14, we default to using a Hamming window in filter design, as it provides up to 53 dB of stop-band attenuation with small pass-band ripple.

Note

In band-pass applications, often a low-pass filter can operate
effectively with fewer samples than the high-pass filter, so
it is advisable to apply the high-pass and low-pass separately
when using `fir_design='firwin2'`

. For design mode
`fir_design='firwin'`

, there is no need to separate the
operations, as the lowpass and highpass elements are constructed
separately to meet the transition band requirements.

For more information on how to use the MNE-Python filtering functions with real data, consult the preprocessing tutorial on Filtering and resampling data.

MNE-C by default uses:

- 5 Hz transition band for low-pass filters.
- 3-sample transition band for high-pass filters.
- Filter length of 8197 samples.

The filter is designed in the frequency domain, creating a linear-phase
filter such that the delay is compensated for as is done with the MNE-Python
`phase='zero'`

filtering option.

Squared-cosine ramps are used in the transition regions. Because these are used in place of more gradual (e.g., linear) transitions, a given transition width will result in more temporal ringing but also more rapid attenuation than the same transition width in windowed FIR designs.

The default filter length will generally have excellent attenuation but long ringing for the sample rates typically encountered in M-EEG data (e.g. 500-2000 Hz).

A good but possibly outdated comparison of filtering in various software packages is available in [7]. Briefly:

- EEGLAB
- MNE-Python in 0.14 defaults to behavior very similar to that of EEGLAB, see the EEGLAB filtering FAQ for more information.

- Fieldrip
- By default FieldTrip applies a forward-backward Butterworth IIR filter
of order 4 (band-pass and band-stop filters) or 2 (for low-pass and
high-pass filters). Similar filters can be achieved in MNE-Python when
filtering with
`raw.filter(..., method='iir')`

(see also`mne.filter.construct_iir_filter()`

for options). For more information, see e.g. FieldTrip band-pass documentation.

On page 45 in Widmann *et al.* [7], there is a convenient list of important
filter parameters that should be reported with each publication:

- filtertype (high-pass, low-pass, band-pass, band-stop, FIR, IIR)
- cutoff frequency (including definition)
- filter order (or length)
- roll-off or transition bandwidth
- passband ripple and stopband attenuation
- filter delay (zero-phase, linear-phase, non-linear phase) and causality
- direction of computation (one-pass forward/reverse,or two-pass forward and reverse)

In the following, we will address how to deal with these parameters in MNE:

Depending on the function or method used, the filter type can be specified.
To name an example. in `mne.filter.create_filter()`

, the relevant
arguments would be *l_freq*, *h_freg*, *method*, and if the method is FIR:
*fir_window*, and *fir_design*.

The cutoff of FIR filters in MNE is defined as half-amplitude cutoff in the
middle of the transition band. That is, if you construct a lowpass FIR filter
with `h_freq = 40.`

, the filter function will provide a transition
bandwidth that depens on the *h_trans_bandwidth* argument. The desired
half-amplitude cutoff of the lowpass FIR filter is then at:
`h_freq + transition_bandwidth/2.`

.

In the Defaults in MNE-Python section, we have already talked about the default filter lengths and transition bandwidths that are used when no custom values are specified using the respective filter function’s arguments.

If you want to find out about the filter length and transition bandwidth that
were used through the ‘auto’ setting, you can use
`mne.filter.create_filter()`

to print out the settings once more:

```
# Use the same settings as when calling e.g., `raw.filter()`
fir_coefs = mne.filter.create_filter(
data=None, # Data is only used for sanity checking, not strictly needed
sfreq=1000., # sfreq of your data in Hz
l_freq=None,
h_freq=40., # assuming a lowpass of 40 Hz
method='fir',
fir_window='hamming',
fir_design='firwin',
verbose=True)
# See the printed log for the transition bandwidth and filter length
# Alternatively, get the filter length through:
filter_length = fir_coefs.shape[0]
```

Out:

```
No data specified. Sanity checks related to the length of the signal relative to the filter order will be skipped.
Setting up low-pass filter at 40 Hz
h_trans_bandwidth chosen to be 10.0 Hz
Filter length of 331 samples (0.331 sec) selected
```

Note

If you are using an IIR filter, `mne.filter.create_filter()`

will not print a filter length and transition bandwidth to the log.
Instead, you can specify the roll off with the *iir_params*
argument or stay with the default, which is a 4th order
(Butterworth) filter.

When use standard `scipy.signal.firwin()`

design (as for FIR filters in
MNE), the passband ripple and stopband attenuation are dependent upon the
window used in design. For standard windows the values are listed in this
table (see Ifeachor & Jervis, p. 357 [3]):

Name of window function | Passband ripple | Stopband attenuation |
---|---|---|

Hann | 0.0545 dB | 44 dB |

Hamming | 0.0194 dB | 53 dB |

Blackman | 0.0017 dB | 74 dB |

For reporting this information, it might be sufficient to read the docstring
of the filter function or method that you apply. For example in the
docstring of `mne.filter.create_filter`

, for the phase parameter it says:

Phase of the filter, only used if`method='fir'`

. By default, a symmetric linear-phase FIR filter is constructed. If`phase='zero'`

(default), the delay of this filter is compensated for. If`phase=='zero-double'`

, then this filter is applied twice, once forward, and once backward. If ‘minimum’, then a minimum-phase, causal filter will be used.

When filtering, there are always tradeoffs that should be considered. One important tradeoff is between time-domain characteristics (like ringing) and frequency-domain attenuation characteristics (like effective transition bandwidth). Filters with sharp frequency cutoffs can produce outputs that ring for a long time when they operate on signals with frequency content in the transition band. In general, therefore, the wider a transition band that can be tolerated, the better behaved the filter will be in the time domain.

[1] | (1, 2) Parks TW, Burrus CS (1987). Digital Filter Design.
New York: Wiley-Interscience. |

[2] | (1, 2, 3) Ifeachor, E. C., & Jervis, B. W. (2002). Digital Signal Processing:
A Practical Approach. Prentice Hall. |

[3] | (1, 2, 3, 4) Vanrullen, R. (2011). Four common conceptual fallacies in mapping
the time course of recognition. Perception Science, 2, 365. |

[4] | Acunzo, D. J., MacKenzie, G., & van Rossum, M. C. W. (2012). Systematic biases in early ERP and ERF components as a result of high-pass filtering. Journal of Neuroscience Methods, 209(1), 212–218. https://doi.org/10.1016/j.jneumeth.2012.06.011 |

[5] | Rousselet, G. A. (2012). Does filtering preclude us from studying ERP time-courses? Frontiers in Psychology, 3(131) |

[6] | Widmann, A., & Schröger, E. (2012). Filter effects and filter artifacts in the analysis of electrophysiological data. Perception Science, 233. |

[7] | (1, 2, 3, 4, 5, 6, 7) Widmann, A., Schröger, E., & Maess, B. (2015). Digital filter
design for electrophysiological data – a practical approach.
Journal of Neuroscience Methods, 250, 34–46.
https://doi.org/10.1016/j.jneumeth.2014.08.002 |

[8] | (1, 2, 3) Tanner, D., Morgan-Short, K., & Luck, S. J. (2015).
How inappropriate high-pass filters can produce artifactual effects
and incorrect conclusions in ERP studies of language and cognition.
Psychophysiology, 52(8), 997–1009. https://doi.org/10.1111/psyp.12437 |

[9] | Maess, B., Schröger, E., & Widmann, A. (2016). High-pass filters and baseline correction in M/EEG analysis. Commentary on: “How inappropriate high-pass filters can produce artifacts and incorrect conclusions in ERP studies of language and cognition.” Journal of Neuroscience Methods, 266, 164–165. |

[10] | Tanner, D., Norton, J. J. S., Morgan-Short, K., & Luck, S. J. (2016). On high-pass filter artifacts (they’re real) and baseline correction (it’s a good idea) in ERP/ERMF analysis. |

[11] | Maess, B., Schröger, E., & Widmann, A. (2016). High-pass filters and baseline correction in M/EEG analysis-continued discussion. Journal of Neuroscience Methods, 266, 171–172. Journal of Neuroscience Methods, 266, 166–170. |

[12] | Kappenman E. & Luck, S. (2010). The effects of impedance on data quality and statistical significance in ERP recordings. Psychophysiology, 47, 888-904. |

**Total running time of the script:** ( 0 minutes 17.115 seconds)

**Estimated memory usage:** 8 MB